This quote is for a packaged pumping system. The pump station shall include all pumps described above, as well as all necessary valves and piping. The variable frequency control panel for the pump station will be mounted to the pump station skid and come prewired and pretested. The system will be controlled by a PLC and HMI-Touchscreen with programming written specific to the project. Control panel is NEMA 12 manufactured for indoor operation. NOTE: Quotation prepared based on the following specifications: Customer supplied design point information only. Quote was prepared with the information noted above. PPS is not responsible for any errors or omissions due to incomplete or inaccurate information.

1) Appropriate power to be provided to pump control panel by others - voltage & phase specified above.
2) Offloading & set up of pump station by others (unless option accepted)
3) This system is manufactured for indoor installation
4) Wet well, concrete pad and/or intake structure to be provided by others.
5) Tie in to mainline and flush lines to be performed by others.
6) Start- up and calibration by a JDGT certified technician. (if option accepted)
7) No taxes are included in this quotation.
8) PPS warrants to the original buyer that its products and systems will be free from defects in material and workmanship for a period of twelve (12) months from the date of placing the Equipment in operation or eighteen (18) months from the date of completion of manufacture of the Equipment, whichever shall occur first.

UL Listed control panel (UL508A)
Main motor shall be VFD controlled
Touchscreen and PLC Pump Control System
PLC bypass operation
Mainline fill routine
Historical system fault log with time and date stamp
Incoming voltage, phase loss or imbalance protection
System fault diagnostic utility
Individual pump run time monitoring
Low flow protection
Low water protection
High & low pressure protection
Service rated disconnect
Automatic pump sequencing
Surge protection
Overload protection on all motors
Incoming power indicator lamp
System fault indicator lamp
Individual illuminated HOA switches
Speed potentiometer for manual speed control

3/8" thick, brake-press folded structural steel skid
Liquid filled suction and discharge pressure gauges
Individual pump check valves and isolation valves
Pump station isolation valves
Stainless steel pressure transducer
Flow switch
All bare steel is coated with Polyester TGIC baked on powder coating
High pressure relief valve
Hose bib connection
Manifold drains

Constructed of marine grade aluminum
Lockable front entry doors
Roll-away roofs for easy service access
Removable side panels for service
Thermostat controlled ventilation fans
Baked on powder coat finish

Payment Terms: All purchase orders are subject to acceptance of factory in Boise. For new customers a receipt of production deposit, verification of acceptable credit, and confirmation of order are required before production. For orders with a value of more than $75K, a 50% production deposit will be required. Balance due 30 days from date of invoice. Late fee of 1 1/2% of the unpaid balance will be charged per month on all accounts which are past due.

Delivery: Delivery dates are estimates and confirmed shipment cannot be determined until all manufacturing details are known. PPS will make reasonable efforts to establish a delivery schedule after receipt of an executed contract and all approvals. PPS shall not be liable for special or consequential damages caused by delay in delivery.

Acceptance: If for any reason buyer is unable to accept delivery at the agreed to date, then delivery shall be deemed completed in PPS's warehouse for purposes of payment and PPS shall store and subsequently deliver as provided above. Buyer will be responsible for additional handling fee of $250.00 and storage charges of $750.00 per month which will be added to invoice.

Lein: PPS retains a security interest in all products sold to buyer until the purchase price and other charges, if any, are paid in full as provided in Article 9 of the Uniform Commercial Code. PPS will file a Mechanics Lien or execute other documents as required to perfect the security interest in the products sold.

Taxes: State, city and local taxes are excluded from the contract price unless otherwise noted. Sales tax will be invoiced on the contract price unless written exemption is provided.

Cancellation: Customers PO's are considered non cancelable. The customer is responsible for all costs associated with canceled orders up to the full contract price of the system.